android problem

[stéphane]

 

Translate
Hello everyone,

Here is my third HI8 happening in my hands and the three I reinstall windows October 1511 th2 all clean and I simply remove the recovery partition.
2 HI8 all went well windows and android are working well.
But on the third Android not boot after 3 reboot I get the recovery I try the Factory Reset nothing to do but it does start.
Windows works as to him.
I just try to reflash android but I get errors with MFT 6.0.43
11/21/15 16: 42: 11,147 INFO: do_new_medfield_device STARTING TO FLASH
11/21/15 16: 42: 11,148 INFO: 0/4/3 Port # 0: DNX / droidboot stage – SN: Baytrail9FA32010
11/21/15 16: 42: 16,012 INFO: 0/4/3 Port # 0: Booting to droidboot.img success – SN: Baytrail9FA32010
11/21/15 16: 43: 01,802 INFO: 0/4/3 Port # 0: Flashing OS
11/21/15 16: 43: 01,802 INFO: 0/4/3 Port # 0: fastboot erase -s Baytrail9FA32010 -S 100M Cache
11/21/15 16: 43: 02,932 WARNING: 0/4/3 Port # 0: Failed to execute “fastboot erase -s Baytrail9FA32010 -S 100M cache”:
erasing ‘cache’ …
FAILED (remote: unable to format)
finished. total time: 1.095s
11/21/15 16: 43: 03,183 WARNING: 0/4/3 Port # 0: Retry to execute Baytrail9FA32010 -S -s fastboot erase 100M Cache
11/21/15 16: 43: 04,294 WARNING: 0/4/3 Port # 0: Failed to execute “fastboot erase -s Baytrail9FA32010 -S 100M cache”:
erasing ‘cache’ …
FAILED (remote: unable to format)
finished. total time: 1.084s

and now AC stops earlier:
1/21/15 18: 20: 53,974 INFO: Ready to flash!
11/21/15 18: 21: 03,724 INFO: do_new_medfield_device STARTING TO FLASH
11/21/15 18: 21: 03,725 INFO: 0/0/3 Port # 0: DNX / droidboot stage – SN: Baytrail9FA32010
11/21/15 18: 23: 05,057 ERROR: 0/0/3 Port # 0: Booting failed to droidboot.img – SN: Baytrail9FA32010

I try the full reset (android and windows) but nothing to do

Could you please help me.

[Tony]

To use Manufacturing Flash Tool with Chuwi Hi8:

1. Make sure Intel-Android driver (IntelAndroidDrvSetup 1.10.0) & iSoC USB driver (iSocUSB-Driver-Setup-1.2.0) are both installed.
2. Download Custom_Config.ini from the link below.
3. Extract it from the .zip file and put it in the Manufacturing Flash Tool’s install directory.
4. Change your Manufacturing Flash Tool settings accordingly as shown in the Chinese tutorial provided in the downloads section for the Hi8.
5. Load the flash.xml from your android ROM using Manufacturing Flash Tool.
6. Plug in your tablet in DnX mode and wait for flash to complete.

http://techtablets.com/wp-content/uploads/2015/11/CUSTOM_CONFIG.zip

NOTE: You will have to reinstall Windows after performing these steps.

[stéphane]

thank you for the tutorial but it’s exactly what I did except for some newer drivers.

[stéphane]

I try with another PC as well as other version drivers but it does not exceed the stage of “11/22/15 12: 46: 16,275 INFO: Ready to flash”.
I do not understand above all that I have another rooter HI8 with ADB so drivers operate.

[Tony]

Try flashing your android BIOS first. Follow the steps in the tutorial for making a bootable USB drive, and download the android BIOS (7mb file). You’ll need a USB drive & USB hub to do this. (Note: this will remove touchscreen support on Windows OS, which you can reinstall later)

[stéphane]

That’s worked.
It was indeed a driver problem I install IntelAndroidDrvSetup1.10.0 and more worries, I could flash without any worries.
I have reinstalled windows 10 in 14min.

Thank you

[Author]

Posts