Two problems after a clean install

Two problems after a clean install

TechTablets › Forums › Teclast Forums › X98 Plus Discussion › Two problems after a clean install

Tagged: , , , , , ,

Viewing 12 posts - 1 through 12 (of 12 total)
  • Author
    Posts
  • January 21, 2016 at 10:25 am #23213
    Anonymous
    Inactive
    • Posts: 10

    Have you tried downloading the drivers from the downloads section?

    January 21, 2016 at 11:05 am #23215
    Downus
    Participant
    • Posts: 7

    Yes, after i used my Double Driver backup, i did a new clean install and used the Drivers in the Download section. Still no results.

    January 21, 2016 at 1:58 pm #23229
    Choum28 .
    Participant
    • Posts: 1

    Download the teclast installation file of december and reinstall your tablet.

    January 22, 2016 at 3:41 pm #23353
    Downus
    Participant
    • Posts: 7

    Problem solved, finally!

    I installed the system files of December and everything is fine.

    Thanks for the help guys.

    January 22, 2016 at 11:33 pm #23405
    Anonymous
    Inactive
    • Posts: 16

    So did you revert back to Teclast image from December or just used the drivers from there. If you have the fresh microsoft image + drivers, whow is the performance?

    January 24, 2016 at 6:31 pm #23527
    Kyriakos
    Participant
    • Posts: 5

    Hi! I have also a problem with the camera after a clean install. It wasn’t installed with the double driver and the packet of drivers downloaded from the forum because of an error. I found out that it doesnt have a digital signature. So I installed it with the procedure of special restart successfully [“Disable driver signature enforcement”]. It worked! BUT when I restart normally,  windows block again the driver and camera is off. What can I do?

    I recovered the system with the tablets recover partion and then used the drivers packets found it forum.

    Everything else is fine. Except an error in device manager for ‘Microsoft Virtual Wifi miniport Adapter-11″ but this is not affecting anything.

    Thank you all!
    Kyriakos

    January 24, 2016 at 7:20 pm #23533
    Kyriakos
    Participant
    • Posts: 5

    A good friend gave me this solution which worked:

    Type in Command Prompt (as admin)

    bcdedit.exe -set loadoptions DDISABLE_INTEGRITY_CHECKS

    (enter)


    bcdedit.exe -set TESTSIGNING ON

    It worked. In the bottom right corner is says “TEST MODE”…

    January 24, 2016 at 7:24 pm #23535
    Samuel Hart
    Participant
    • Posts: 50

    If you’re going to run unsigned drivers you need to keep that security setting off.

    January 24, 2016 at 7:25 pm #23536
    David
    Participant
    • Posts: 42

    I use this drivers and all works perfectly

    https://mega.nz/#!FsxiRQ5Q!r0aHnWabQK-h7DsbRoaUNm6ZiCvYYc464UerSPOkGHY

    January 24, 2016 at 7:55 pm #23541
    Kyriakos
    Participant
    • Posts: 5
    David wrote:

    I use this drivers and all works perfectly https://mega.nz/#!FsxiRQ5Q!r0aHnWabQK-h7DsbRoaUNm6ZiCvYYc464UerSPOkGHY

     

    Interesting pack… But it needs better knowledge to manually do the procedure. (Double driver is easier) I’ll try it! 🙂 THank you! Maybe we could add this RAR in the forum of TECLAST x98 plus

    January 24, 2016 at 8:45 pm #23552
    Samuel Hart
    Participant
    • Posts: 50

    Where do you find this Double Driver for the x98 plus?

    January 24, 2016 at 9:29 pm #23555
    Kyriakos
    Participant
    • Posts: 5

    http://techtablets.com/wpfb-file/double_driver_4-1-0_portable-zip/

    and drivers: http://techtablets.com/downloads-drivers-roms/

  • Author
    Posts
Viewing 12 posts - 1 through 12 (of 12 total)
  • You must be logged in to reply to this topic.

Lost Password

Skip to toolbar