X98_PRO_android_5.1_mirek190_v6.0 rom

[M.V.]

Tried to install your awesome rom, but if i  boot to dnx mode and then plug it in, i click twice on your flash bat, i see fast some lines and then it closes the windows. After that i tried to start as admin but there comes only the message “cant find specified path”.

Solutions? 🙂

[Richard Davidson]

Thanks for v2.

Will I get the full benefits etc by doing the dirty update to v2, I did v1 as a clean install.

[Milosz]

Guys I got problem. After bios update i going to DNX MODE to flash Mirek ROM. But PC don’t recognise tablet…nothing happen. I installed all this 3 driver ,iSocUSB Drive, IntelAndroidDrive, PhoneFlashTool but no results. I did test on laptop also same think. Phone flash tool don’t see device- Mirek flash tool give me (waiting for device)…Any idea? THX

[mirek]

Tibor said :

 

One important thing before the flashing, though: before entering the DNX mode, X98Pro has to be switched off from Android, not Windows, before flashing. Otherwise it would not be recognized by the PC. I tried several USB cables and all the USB ports that I have on my PC, but with X98Pro switched off from Windows – no success! After I rebooted X98Pro into the Android, then switched it off in Android – voila, everything went smoothly and quickly! Thanks once again, now trying to test the performance and stability, because I was absolutely disappointed with the original ROM…

Milosz –> have you tried ?

 

[mirek]

Salvi wrote:

mirek wrote:

Salvi wrote:

@mirek Thx again for the ROM, the real difference with the previous release I think is the battery drain, now is much better! Do you think that we can reach a much better optimization on battery side (downclock/undervolt/etc.)? This is the huge defect of this tablet.. with my old nexus 7 (tegra) on android I reach 7/10 days in aero mode & screen off; with this -on android- only 10 hours (aero+screen off) if I’m lucky. :/ I think that a 8000Mah battery should perform better. 1) Anyone of you guys have any advise to reach a better endurance on android (can the cpu be undervolted with this rom?)? 2) Is there a way to use an active flip case? Without the light sensor the screen doesn’t feel the sensor covering act made by the flip, so the screen stay off. THX a lot!

What is mean “areo mode” ? In android ? Your device losing the whole battery in 10 hours in sleep ? I loose around 1-2 % within 10 hours . I improved battery live alnost 50 % in normal usage in v2 rom ( Internet , reading , music , light games ). And yes I still can improve battery live even more … but it needs more tests .

Air mode, sorry I wrote it wrong: no wifi/no bluetooth. I compare this tablet to my old nexus 7 on the same state, so screen off & air mode and… This tablet do mainly 10hours vs 10days of nexus. How can I improve this? How can I reach your better battery consuption? Any possibility to undervolt the single cpu states or totally switch off some cores? Thx really for your work and for all you answers! <noscript>​</noscript>

Look

After 10 hours in sleep from my x98 pro -like you see is around 1 -2 %

try to find the app which cause the problem of draining the battery

 

 

 

Attachments:

You must be logged in to view attached files.

[valerima]

hi,

if you have k9c3 with dual bios and have windows only, but no android yet, how you make it recognizable, android is boot option only , but no this OS…How?

valerima

[Dominik]

valerima wrote:

hi,

if you have k9c3 with dual bios and have windows only, but no android yet, how you make it recognizable, android is boot option only , but no this OS…How?

I dont think you can flash Mireks rom using Mireks tool as first after getting K9c3 dual boot. First one You have to flash rom using PhoneFashTool to get all partitions (As blank i think, You lost all windows data).
To get DNXmode recognize try go into mode via BIOS: http://techtablets.com/forum/topic/tool-for-bios-update_-k9c3_-afuwin/page/2/#post-20162

Everything about getting K9C3 dual boot is in here: http://techtablets.com/forum/topic/how-to-dualboot-androidwindows-on-k9c3/

[M.V.]

Found my problem. I can only boot into DNX Fastboot Mode and not DNX Mode. So if i boot with only volume- i boot in DNX Fastboot Mode… i i press vol+ & – i boot in the same mode. So i cannot flash anything?

[Ruoska]

M.V. wrote:

Found my problem. I can only boot into DNX Fastboot Mode and not DNX Mode. So if i boot with only volume- i boot in DNX Fastboot Mode… i i press vol+ & – i boot in the same mode. So i cannot flash anything?

DnX fastboot is right one and seems you can get there. Does your pc recognize your tablet? If not try to turn tablet down from android side and then go to DNX fastboot.  And you previous post you said you clicked flash bat which doesn’t sound like its right file, you should use mirek’s flashing tool FLASHER_1.1.

 

[M.V.]

Yeah right, i booted into DNX Fastboot Mode and double clicked the following file: “FLASHER_v1.1-(-just_press_twice-).bat” but it closes immediately
My tablet was recognized from my windows.

[Karl0ss]

Brilliant rom, good work mate, still seems to run pretty hot, but a massive improvement..

flashed 2.01 without any issues.

[mooms]

mirek wrote:

Strange I was installing many apps ant the same time and never freezes for even a seconds … and was using browser and checking other apps in play store at the same time – zram was working perfect buffering ram data I testes that app you mentioned – works ok. Have you flash clean system ? Do you have k9c3 or k9c6 ?

K9C6 & clean flash.
Maybe the freeze in Perfect Viewer was because I have a lot of comics
This ROM have very good battery life, finally I can keep the tablet in sleep mode, no need to power off, great work mirek!

[M.V.]

Deleted all drivers, rebootet and installed them with correct order new.
My Tablet would be recognized at windows in DNX Fastboot mode as “intel android ADB interface device” but “FLASHER_v1.1-(-just_press_twice-).bat” still won’t work.

After Removing ” IF %ERRORLEVEL% == 3 GOTO EXIT

:EXIT
exit”

from flash bat it finally works.
Some ideas mirek why it immediatly closes? Seems like something always ticks option 3 and closes the flash process.

Maybe because i have num pad activated?

Edit: Worked so far, but it seems your “tool” always chooses last option for me without asking me what to choose… strange…

[mirek]

M.V. wrote:

Deleted all drivers, rebootet and installed them with correct order new. My Tablet would be recognized at windows in DNX Fastboot mode as “intel android ADB interface device” but “FLASHER_v1.1-(-just_press_twice-).bat” still won’t work. After Removing ” IF %ERRORLEVEL% == 3 GOTO EXIT :EXIT exit” from flash bat it finally works. Some ideas mirek why it immediatly closes? Seems like something always ticks option 3 and closes the flash process. Maybe because i have num pad activated? Edit: Worked so far, but it seems your “tool” always chooses last option for me without asking me what to choose… strange…

Can you post edited working .bat file ?
It looks like you had pressed all the time E button –> that closes the tool.

I suspect something with text encoding …maybe
And what of windows you are using and your native language of windows.

[Frank]

Richard Davidson wrote:

Thanks for v2. Will I get the full benefits etc by doing the dirty update to v2, I did v1 as a clean install.

I had no problems with my dirty upgrade from V1, Richard – works PERFECTLY. Mirek deserves loads of donations!

[Author]

Posts