Thanks for sharing your precious time to create this post, It so informative and the content makes the post more interesting. really appreciated.

cookie clicker

Cool, i might have to do this too

The best will be Apple iPad Pro 4th Generation and Samsung Galaxy Tab S7 512GB  in 2021

Thanks for advice. I also  work with windows 10.

<span data-sheets-value=”{"1":2,"2":"Nakivo"}”…[Read more]

Same problem from my side, can’t really find a replacement.

In my list there is : Zte Axon 20 5G extreme edition

and: Redmi K40 Pro +

I’m open to discuss with everybody as my MiMax3 is a little bit slow and the battery is dying. I bought a spare battery just in case.

I have 2 Jumper Ezbook 3 pro. One of them don’t detect the m.2 ssd disk intermitenttly.
I opened the rear cover and see that the m.2 adapter as similar to the showed in the pictures but with different part number P314-ssd-Rev01.
But I don’t find where buy one

Hi i’m trying to install Mirek custom ROM but when Manufacturing tool starts it reaches 6% and then it closes, can anyone say me what to do?

thank you bro you make my day root don

need more details but wonderful thank u

Try to leave the rear cover, disconnect the battery and leave the notebook discharge the capacitors. I think you can reset te bios.

Because we really want to take advantage from the actual USB-C port.

Here is my experience:

1. Using a D-LINK DUB‑M420 it works fine, I do have HDMI output while charging with original charger and also I can use USB A ports. With any other PD charger (powerbank 18W and usb c PD power brick of 30W) it simply do not charge either directly or t…

[Read more]

Seriously, why not just use the micro usb port. I use it with my hub, works perfectly fine.

Just got mine. I have to disagree, build quality is awesome. I find people are just to heavy handed these days. All batteries of these type expand, due to heat, over charging, etc etc.

My two year old Ezpad 6s Pro, did exactly the same thing. It was pushing my screen out from front. Being an engineer, I expelled gases.  I DON’T RECOMMEND…[Read more]

Does anyone else have a Teclast F5 for a year or so and didn’t suffer from the swelling issue? I like this laptop but the build quality is low and I’m afraid I could expend some money replacing the battery and run into the same or a different hardware issue soon so I’m not sure what to do.

Sorry Nok, that was 5 years ago…

Firstly, I sent the faulty unit via the UK Official Distributor.

Although a thoroughly good job was done, it was probably not cost effective.

The link for the firmware and a description of how to do it is at the top of this thread.

Last line reads ‘Everything you need plus additional information can be downloaded’

Click on the RED ‘Here’.

It…[Read more]

from which country did you sent it to china? Could you tell me more about the process? And where to get this firmware from?

from which country did you sent it to china? Could you tell me more about the process? And where to get this firmware from?

hi, Unfortunately the problem with my iWork 11 was the main memory chip. It was sent to China and repaired.

It came back fully installed.

I have however, managed to fully clear and install my small Onda tablet.

The process may well be similar.

I attach the word document to provide guide lines only.

You will still need all the correct firmware…[Read more]

hello adramel and xeun. I have Cube Iwork 11 i8t Could you please help me here, I am able to access bios but unable to install windows as it is showing unallocated space of 8Gb and no other space. I am unable to create a partition

could you please guide me here.

[email protected]

please contact me.. need help

Thanks Werner. Would you let me know which clonezilla  you used before?