UPDATE: I finally got the auto rotating into tablet mode working on a clean windows install that I have used.

I managed to download the drivers from the BMax website which for some strange reason turned to a OneDrive link whereas as it was a Baidu link yesterday.

I then unpacked the drivers and ran the setup.cmd and went through all the driver…[Read more]

Hey guys, I’m really struggling with my Y13 at the moment. I install a fresh version of Windows only to then realise the tablet mode doesn’t work. I have since then downloaded the windows install files above and gone through the applying image stage, however, when it finishes applying and reboots I just just a black screen instead of Windows…[Read more]

Hi,

I am having the following issues after reinstalling windows:

• Touchscreen does not work (either by hand or using the pen)
•  Rear Camera installed as System Device but not available on camera app
•  On Device Manager, 2 devices are not known.

I tried all of the following:

• Updating Windows to the maximum and every driver it suggested t…

[Read more]

Thanks did you have to make a Baidu account and use their downloader software to get the drivers?

I just tried it and it and it got me into the download area. The code for the Y13 is ‘H2M1’. If you do manage to fix the issue can you post some instruction back here please.

I really don’t think that this is the case because when I set the maximum performance in intel graphics plan in power options it doesn’t lower the clocks and also at high performance settings I don’t get even a second of clocks higher than 450 Mhz. At 50 degrees cant be thermal throttling. I will try to make a new installation of windows rather…[Read more]

Benjamín, a todas tus preguntas SI.

Te adjunto foto.

Un saludo

Would it be possible for someone to send me the HingeAngle Service download please? I have tried to access the download page on the BMax page however it will not accept my pin on the bottom of my Y13? Thanks

@georgo85 I read that with some devices, such as yours, there might be a power draw limit in the EC (Embedded Controller) on the motherboard. Not much you can do about it. With my Teclast F15, I got best results by unlocking the power limit to 12W max. If I go 15W, there is thermal throttling, because I haven’t done any thermal modding yet. You…[Read more]

You should use the third party IPTV app on your phone for watching latest movies, TV shows, sports or anything…

I bought a DogFish 120GB SSD. First drive died after 1 days constant use. They replaced it and been using replacement nonstop for 9 to 10 hours a day.

I have gone a bit nuts on my pimping of my 6 PRO. Did the Shim mod (x2) and the SSD install, now im going to remove shims and attempt to fits the worlds smallest fan into it, :). I have some good…[Read more]

You have altered boot order in BIOS?

EFI is one of the options as first boot device.

Sooo after a lot of research (I really like max Mhz in my gpu :P) I found that actually the intel graphics plan in power options doesn’t affect the gpu clocks at all, as you can see in screenshots.

It seems that it is stuck at balanced at all times at 450 Mhz max not even a little spike at 700Mhz. I tried change it with Control Panel for Intel…[Read more]

Yes I restored the WIN10 Image successfully.

I use the Xiaomi 6A device for gaming. Normally, I’m playing Resident Evil game on my device smoothly. So, I recommend it…

Have you checked if the ssd comes up in the bios under “Chipset”->”South Cluster Configuration”->”Sata Drives”

And check if you:

-have Chipset SATA enabled

-have Port 0 enabled

-have Sata Device Type on “Solid State Drive”

-have something showing up after “Sata Port 0” like your ssd’s name

Greetings

Benjamin

See https://techtablets.com/forum/topic/drivers-for-ezpad-6-pro/page/4/#post-149718

Check which touchscreen model you have (a / b). What kind of problem do you have with your touchscreen?

If it generates touches on seemingly random spots and does not repond corectely then that issue can be fixed with the right driver.

Greetings

Benjamin

Enter bios with ESC

3x right for “Chipset”

3x down for “Uncore Config”

4x down for “Integrated Graphics Device” (I guess that’s the one you changed)

Enter

1x up for enable

Enter

Esc (Save and Exit, defaults to yes)

Enter

If this is not working please let me know…

(See images for orientation)

Greetings

Benjamin

Hi Murice,

according to https://youtu.be/WUVNKHqBOUU?t=133

there the storage is soldered directly to the mainboard, so you will be unable to expand it.

So options which do not involve soldering would be using an usb stick or an sd card.

They will appear as an extra storage, just like they would show up on any other pc.

Greetings

Benjamin

I had issues running the complete unlock via batch file or on boot. My way around it was to open RWeverything and then insert the commands and hit enter. Get the confirmation it worked and then I got 700Mhz and 2.3Ghz overall 4 cores.  Couldn’t quite get what Henk had for pulling 15W.